Regulator PRO / LITE

Regulator of position of transducer PRO

STRONGER_01

Regulator of position of transducer LITE

STRONGER_02

Description of models of regulators of transducers sonic depth findersThis device is intended for getting / up of lowering and regulation of correct angle of slope of transducer sonic depth finder. It is necessary for the exact reflection of data echo of location in the cases of different trim of boat on a stern or on her nose. For the correct reflection of data of transducer must be strictly in parallel to the water smooth surface (to horizon). Thus, almost all manufacturers of echolocation equipment recommend installing their transducers. The reflected in this case signal got to them will most correctly represent information on the screen of your device!

Eng_bulletin

On a picture the variants of angles of slope of transducer, and also variants of fish, are higher presented on the screen of sonic depth finder. Overhead two pictures show wrong position of transducer, such position of sensor is possible either during the wrong primordial setting or in case of presence of longitudinal trim on a stern or on the nose of boat (more often – on a stern). Only in the case when a sensor is located strictly in parallel to horizon, information on the screen of your sonic depth finder is represented clearly and without distortions (lower picture). But an analogical situation takes place and with the picture of bottom of reservoir. At wrong position of sensor of transducer the real picture is so much distorted on the screen of your device. Therefore it is very important to obtain the correct angle of slope of transducer!

Boat depending on the amount of passengers, load placed on it, and also his weight and place of placing, yields to the longitudinal axial heel that in turn, can be directed both in nasal part and in feed part of boat. In investigation what the regularly set sensor in different situations not always represents information correctly.

Our device is sent exactly to that, to have the opportunity of remote electronic regulation of angle of slope of transducer.

During the protracted speed transitions, and also during the stand of boat, or in case, options of boat on a gun-carriage, you can heave up transducer on a maxheight practically in parallel to the stern of boat and to clean unnecessary resistance of sensor of sonic depth finder the same at water, to prevent becoming overgrown with transducer water-plants during a stand, and also to prevent breakage of sensor at a collision with water barriers or bottom of reservoir at going of boat a stern near a bank and on shoal.

регул3

Also getting up of sensor of transduser is very important in the moment of loading and further transporting of boat on a gun-carriage. For this purpose you press the key with a pointer upwards on the bearing-out button, or on control panels and sensor automatically will go up to eventual position.

We hope that by means of this device fishermen and active rest lovers on water will be able to improve quality, and also safety fishing on water, due to clear information that they will be able to get from the screen of the sonic depth finder! Well and certainly substantially to economize the budget on the purchase of new transduser!

Fastening of transducer to the regulator of STRONGER

For fastening of sensor to the regulator you must drill opening in the plate of regulator, what they corresponded to the location of opening of fastening of трансдьюсера, as shown on a picture below:

регул2регул1

After setting of regulator on the stern of boat you must initially propose a sensor according to recommendations of producer of sonic depth finder. In future all regulation and tuning of sensor to the real terms will take place remotedly from the place of management by your cutter.

Setting of regulator of STRONGER

Setting of regulator comes true on the same principle, as well as ordinary fastening of transduser on the stern of boat described in guidance on exploitation by a sonic depth finder. Important, that a regulator and sensor of sonic depth finder did not come forward for the edges of boat and did not create additional hindrances the same in his work.

Management by the regulator of STRONGER by means of the bearing-out button (version of LITE and PRO)

The bearing-out button is supplied in a base complete set.

STRONGER_06

By means of her you will be able to lift and drop трансдьюсер. Similarly you will be able brief pressures on the key подрегулировать a sensor in position that can be defined by means of arcs of fishes on the screen needs to you. But unfortunately, this option is not entirely convenient, since there is no possibility of visual control of the sensor position.

Management by the regulator of STRONGER by means of control (only for PRO of version) panel

A panel and control unit kit is available as an option for the regulator.

STRONGER_07

By brief pressure (1 sec.) on the buttons (MAN) you can obtain regulation of angle of slope of sensor with exactness of setting to 2 degrees for one pressure on the button with a pointer upwards or downward. It will allow to find optimal, most  position of angle of slope of transducer you, that accordingly will help to get the most exact information on the screen of your sonic depth finder.

If you fish alone, or by a the same command, and use practically the same weight of load and place him in the same places, saving the the same longitudinal trim of boat, then by means of the button (M), by pressure and withholding during 7-8 seconds, you can fix for itself the so-called “favourite position” of angle of slope of sensor of трансдьюсера. In this case you will be always able to go back to the “favourite position” after any manipulations with a device, simply briefly (1 sec.) pushing the button (М), and a device automatically will set the sensor of трансдьюсера in your “favourite position” that was before stored in memory. Even in case of deenergizator from CU a device, information about “favourite position” is saved in his energyindependent memory of device up to a next change by you this “favourite position”.

A device does not have analogues in the world. A company STRONGER has patent rights on this invention.

00010002

Delivery of LITE / PRO set

Regulator
Lite /  Pro
Wires for connection
Yes /  Yes
Bearing-out button
Yes / Yes
Roofing timbers
Yes / Yes
Control panel
No / Option
Control block
No/ Option
Complete set of wires for CU
No/ Option
Instruction
Yes / Yes
Warranty sheet
Yes / Yes

 Technical descriptions of LITE / PRO

Axleloading
100 n /  200 n
Current on-loading
 150 ma /  250 ma
Current no-load
45 mA / 75 mA
Tension
12 v / 12 v
Climbing ability is lowering
5 мм/c / 3,5 мм/c
Primary coolant
air / air
Method of cooling-line
water is air / water is air
Libra of transducer
to 300 gramme / to 1000 gramme
Time of continuous work
2 mines / of 2 mines
Overall sizes of regulator
360 x 80 x 65 мм / 360 x 80 x 65 мм
Overall sizes are in packing
420 x 250 x 65 мм / 420 x 250 x 65 мм
Libra
1 kg / of 1 kg
Guarantee
1 year/ 1 year
Model number
RL 100 / RL 200